Jan 15, 2024 Leave a message

Plastic Crusher Common Faults And Solutions

The invention of plastic shredder in our lives and industrial production are very important, its birth let us no longer for the plastic pollution headache, the reliability of plastic shredder operation direct production efficiency and the normal operation of the following process, therefore, maintenance and operation personnel learn to analyze and deal with the common failures of the shredder system, and in the short term to be eliminated, as soon as possible to resume production, It makes things seem more important.

First, vibration crusher generally uses a direct motor connection crushing device, this connection is simple and easy to maintain. However, if the two are not well connected during the assembly process, it will cause the overall vibration of the crusher.

1, motor rotor and crusher rotor different heart. The position of the motor can be moved left or right, or the foot of the motor can be padded to adjust the concentricity of the two rotors.

2, crusher rotor different heart. The reason is that the two supporting surfaces of the rotor shaft are not in the same plane. The bottom surface of the supporting bearing seat can be covered with copper, or an adjustable wedge iron can be added to the bottom of the bearing to ensure that the two shaft heads are concentric.

3. The vibration of the crushing chamber is large. The reason is that the connection between the coupling and the rotor is different or the quality of the flat hammer inside the rotor is not uniform.

4. The original balance is disturbed. After the motor repair, the dynamic balance test must be done to ensure the overall balance.

5, the foundation bolt of the crusher system is loose or the foundation is not strong, in the installation or maintenance, to evenly tighten the anchor bolt, between the foundation and the crusher, to install a shock absorber to reduce vibration.

Overheat bearing is a more important part of the crusher, and its performance directly affects the normal operation and production efficiency of the equipment. During the operation of the equipment, the user should pay special attention to the temperature rise of the bearing and the noise of the bearing part, and the abnormal should be dealt with as early as possible.

1, 2 bearing seat uneven, or motor rotor and crusher rotor different heart, will make the bearing affected by additional load, resulting in overheating of the bearing. In this case, it is necessary to immediately stop the fault to avoid early damage to the bearing.

2, too much lubricating oil in the bearing, too little or aging is also the main cause of bearing overheating and damage, therefore, according to the requirements of the use of the book on time and quantitative filling of lubricating oil, general lubrication accounts for 70%-80% of the bearing space, too much or too little is not conducive to bearing lubrication and heat transfer. The bearing extends its service life.

3, the bearing cover with the shaft is too tight, the bearing with the shaft is too tight or too loose will lead to the bearing overheating. Once this problem occurs, there will be a grinding sound and obvious swing in the operation of the equipment.

The blockage of the mill is one of the common faults in the use of the mill, and there may be problems in the design of the machine, but more is caused by the improper use of the operation.

1, the feed speed is too fast, the load increases, causing blockage. In the feeding process, we should always pay attention to the ammeter pointer deflection Angle is large, if the rated current is exceeded, it indicates that the motor is overloaded, long-term overload will burn the motor. In this case, the feed door should be reduced or closed immediately, and the feeding method can also be changed to control the feed amount by increasing the feeder. There are two kinds of feeders, manual and automatic, and users should choose the right feeder according to the actual situation. Due to the high speed of the mill, the load is large, and the load volatility is strong. Therefore, the current of the mill is generally controlled at about 85% of the rated current.

2, the discharge pipe is not smooth or blocked feed too fast, will make the crusher tuyere clogged; Improper matching with the conveying equipment will cause the wind of the discharge pipeline to weaken or block after no wind. After finding out the fault, it should first clear the delivery port to change the mismatched conveying equipment, adjust the feed amount, so that the equipment can operate normally.

3, hammer fragment, aging, screen hole closure, tattered, crushed material water content is too high will make the crusher blocked. The broken and severely aged hammer should be regularly updated to maintain the good working condition of the crusher, and the screen should be regularly checked, and the water content of the crushed material should be less than 14%, which can improve the production efficiency, but also make the crusher not blocked, and enhance the reliability of the mill.

To learn more about our Fangyuan products, please click this link :https://www.fine-mill.com/products.

Send Inquiry

whatsapp

Phone

VK

Inquiry