Nov 30, 2023 Leave a message

Crusher common problems and solutions

First, the type of crusher understanding

The process of changing large particle materials into small particle materials with external force is called crushing. The machinery used is called a crusher. Common types are as follows:

1, jaw crusher

Jaw crusher is usually used to break all kinds of hard mines and rock rough crushing. The working principle of the jaw crusher is that the movable jaw plate is periodically near or away from the fixed jaw plate, so that the material entering the crushing chamber is crushed by extrusion, splitting, bending and impact.

2, impact crusher

Impact crusher is mainly through the rotor driven plate hammer crushing materials. Combined with the impact of the counter plate and the collision of the material itself to achieve the complete crushing of the material. It is suitable for crushing hard rock and brittle particle materials whose compressive strength does not exceed 350MPa.

3, cone crusher

Cone crusher is suitable for crushing or fine crushing operation, cone crusher working process, the motor through the transmission device to drive eccentric sleeve rotation, the moving cone in the eccentric shaft sleeve forced to do rotation swing, the moving cone near the static cone section is a crushing chamber, the material by the moving cone and static cone multiple extrusion and impact and broken. When the moving cone leaves the section, the material that has been broken to the required particle size is discharged from the bottom of the cone under the action of its own gravity, thus completing the crushing.

4, hammer crusher

The hammer crusher mainly relies on the impact energy to complete the crushing material operation. When the hammer crusher is working, the motor drives the rotor to rotate at high speed, the material evenly enters the crusher chamber, and the high-speed rotating hammer head impacts and cuts the tear.

5, impact crusher

The impact crusher is also known as the sand making machine, which is simply the principle of stone beating stone. Let the stone collide with the stone accelerated by the impeller in the process of natural fall, so as to achieve the purpose of crushing, and the stone accelerated out of the stone and the natural fall of the stone collision formed a vortex, and broke twice in the process of return. It is mainly used for soft, medium and hard materials such as crushed ore, machine-made construction sand and metallurgical slag.

6. Shredder

Mainly through cutting tools to cut and tear the material to form a crushing and refining effect on the material. Mainly used in industrial waste, household waste, paper mill waste, electronic waste and other solid waste. Sreed company is the leading domestic shredder R & D and manufacturing enterprises. Main product types: single axis shredder, double axis shredder, four axis shredder, large coarse crusher.

The single-axis shredder mainly gnaws the material through the tool on the knife roll, and then forms shear with the fixed knife, and controls the final discharge particles through the screen. Mainly used in crushing plastic, wood and other dry materials.

Dual-axis shredder mainly through the relative rotation of two knife rollers, the cutting edge of the tool and the cutting edge formed between the hook will tear the material to achieve the crushing effect. Double-shaft crusher has a wide range of applications, can break rubber, metal, wood, fabric and other brittle and flexible materials.

The four-axis shredder mainly through the upper tool group will hook the material to the lower tool group, and then the lower tool roll relative rotation, the cutting edge between the cutting edge and the cutting edge at the same time the hook will tear the material, the particle size is less than the screen material from the mesh, the material larger than the mesh is returned to the knife box for two or more crushing, until the material can be in line with the screen so far. Four-axis crusher is mainly used in crushing brittle materials such as home appliances, electronic waste, rubber and wood.

Large coarse crusher mainly through two groups of independent tool group, through the hydraulic system to drive the tool group for large torque rotation, the blade and the fixed knife to form tearing shear to form crushing. Large-scale crusher is mainly used in the coarse crushing of large output of domestic waste, such as domestic waste power plants, large domestic waste treatment plants, cement kilns and domestic waste disposal and other occasions.

In the production process of cement, most of the raw materials are broken through the crusher, such as limestone, clay, iron ore and coal. Limestone is the main raw material of cement, the grain size after mining is larger, the hardness is higher, so the crushing of limestone occupies a very important position in the crushing of cement plants.
Second, crusher equipment daily use and maintenance precautions

1, crusher precautions

Iron removal is an important measure to ensure the safe operation of crushing equipment. Especially for the spring cone crusher is more important. Because, although the spring cone crusher is equipped with a spring safety device in the structure, the internal discharge port is small, and it is often stuck by large pieces of metal, causing equipment accidents and stopping production. At present, the commonly used iron removal equipment in production includes suspension magnets, electromagnetic rollers and metal detectors, and many selection plants have realized iron removal automation.

Crusher in the daily use process, the need for daily maintenance, but also pay attention to reasonable use, so as not to cause damage to the machine. Daily maintenance of crusher:

Before the test start, it is necessary to strictly check whether the installation of each part of the machine meets the requirements, whether the screws and bolts are loose, and whether the belt can be gently pulled by hand to test the case. At the same time check the direction of rotation, it is strictly prohibited to crush flammable and explosive items, so as to avoid accidents.

In the production, uniform feeding should be maintained to ensure the crushing quality and normal production of the crusher, and it is strictly prohibited to overload the motor to ensure the normal operation of the machine.

In addition to often paying attention to checking the tightening and loosening of various parts, pay attention to checking the wear of wearing parts, such as serious wear should be replaced in time to avoid damage to the main parts.

Often check the tooth plate wear of the crusher, such as serious wear to replace the tooth plate in time, so as not to cause particle size phenomenon.

Due to the high speed of the crusher, in addition to the correct and firm installation, good lubrication should be maintained to maintain the normal operation of the machine. Under normal circumstances, the bearing temperature does not exceed 70 degrees. The main engine bearing is added once a week butter, molybdenum disulfide, high-speed butter effect is better.

2, crusher use and maintenance

No matter how the crusher is fed, there must be a reliable rust removal device to prevent other chores from entering the crusher.

The crusher must be started without load, and the retained materials in the crusher must be checked and removed before starting.

If the crusher is disabled for a long time, or the first start, it should be manually rotated for 2-3 weeks in advance, to confirm that the machine runs freely, and then the motor "point" several times, when the motor rotation direction is correct, the crusher can be officially started.

Start the crusher to reach the normal speed, and in the absence of abnormal conditions to start feeding.

The main points of maintenance of crusher three faults

Crusher equipment as the main equipment of mining, mainly for the size of different stone crushing, crusher equipment mainly has jaw crusher, impact crusher, impact crusher, double roll crusher, hammer crusher and cone crusher and other equipment.

Three, crusher troubleshooting points

Crusher three major faults: bearing fault repair, shaft fault repair and fixing, rotor core fault repair. Here we will analyze the three main points of troubleshooting:

1, bearing failure repair worn parts

The rotating shaft rotates through the bearing support, which is the most heavy part of the load and the part that is easy to wear.

Fault check

In-operation inspection; When the rolling bearing is short of oil, it will hear the sound of "rolling rolling"; If you hear a discontinuous "stem" sound, it may be the bearing ring is broken. When the bearing is mixed with sand and other debris or the bearing parts are slightly worn, a slight noise will be generated.

Inspection after disassembly; First check the crusher bearing rolling body, the inner and outer steel ring is damaged, rust, scars, etc., and then pinch the bearing inner ring with your hand, and make the bearing balance, the other hand push the outer rigid ring, if the bearing is good, the outer steel ring should rotate smoothly, there is no vibration and obvious stagnation phenomenon in the rotation, and the outer steel ring does not regress after stopping. Otherwise, the bearing can no longer be used. The left hand jams the outer ring, the right hand pinches the inner ring, and pushes it hard in all directions. If it feels loose when pushing, it is seriously worn.

Fault repair: the rust on the outer surface of the bearing can be erased with sandpaper and then cleaned in gasoline; Or when the bearing is cracked, the inner and outer rings are broken or the bearing is excessively worn, a new bearing should be replaced. When replacing a new bearing, choose the same bearing as the original model.

2. Shaft failure maintenance

Journal wear; When the journal wear is not large, a layer of chromium can be plated on the journal and then ground to the required size; If the wear is too much, it can be surfacing welding on the journal, and then cutting and polishing on the lathe; If the journal wear is too large, it is also turned on the journal 2-3mm, and then a sleeve is turned on the journal while it is hot, and then turned to the required size.

The shaft is bent; If the shaft bending of the crusher is not large, it can be repaired by polishing the journal and sliding ring. If the bending is more than 0.2mm, the rotating shaft can be placed under the press, and the pressure is corrected at the beat bend, and the surface of the corrected shaft is polished by the lathe; If the bend is too large, a new shaft needs to be replaced.

Fourth, fixed, rotor core fault repair

The stator and rotor are composed of mutually insulated silicon steel sheets, which are part of the magnetic circuit of the motor. The damage and deformation of rotor core are mainly caused by the following reasons.

Crusher bearing excessive wear or poor assembly, resulting in fixed rotor friction, the surface of the iron core damage, resulting in short circuit between the silicon steel sheet, motor iron loss increase, the motor temperature rise too high. At this time, the application of fine file and other tools to remove burrs, eliminate the silicon steel sheet short, clean up the insulation paint, and heat drying.

Excessive force when removing the old winding caused the tooth slot to skew and open outwards. At this time, tools such as needle-nose pliers and wood hammers should be used to trim, so that the grooves can be reset, and hard insulating materials such as green shell paper and rubber wood should be added between the silicon steel sheets with gaps that are difficult to reset.

The surface of the iron core is rusted due to moisture. At this time, it is necessary to sand it clean and apply insulating paint after cleaning.

High heat is generated around the joint ground to burn the core groove or tooth. Use chisel or scraper and other tools to remove the deposition clean, coated with insulating paint drying.

If the connection between the iron core and the frame is loose, tighten the original positioning screws. If the positioning screw fails, redrill the positioning hole in the frame and tap to tighten the positioning screw.

Five, crusher hammer is how to do repair work?

The hammer head is the key component of the rotary body of the crusher, which is generally made of high wear-resistant high manganese steel. Crusher hammer plate is divided into 8 equal parts along the circumference, and is equipped with 36 hammer heads, adjacent hammer heads staggered arrangement, hammer heads can be 360° full rotation. Let's look at the repair work of the crusher hammer head.

The restoration of the hammer head

The crusher generally has 36 hammer heads, which are the key components of its crushing material, and therefore, are also most vulnerable to wear. When the front edge of the hammer head is worn to a certain extent, the hammer head can be used, and the worn hammer head can be repaired by surfacing with wear-resistant alloy, which can greatly save the consumption of metal materials.

Six, hammer installation standards

The installation of the hammer is extremely strict, must be accurate weighing, the following is the specific standard: on the working cylinder of the rotor, the weight of the hammer in the same radial plane should be equal to or close to each other; On the working cylinder of the rotor, the total weight of the axially symmetrical hammer head should be equal to or close to each other, and the maximum deviation should not exceed 0 ~ 20kg; The arrangement of hammer heads in the same row along the axis is weighted in the middle, and the weight is decreased or staggered to both ends.

The hammer is the main working part of the crusher, and its quality directly affects the production efficiency of the crusher, so when in use, we must check regularly and do a good job of maintenance.

The plate hammer is in direct contact with the material, so the consumption of the plate hammer has been too large, and the main form of damage to the plate hammer is loose and broken, rather than normal wear. The loose and broken plate hammer, light will break the bolt and other plate hammer, damage the rotor body and counterattack frame, heavy will break the rotor shaft, tear the rotor body, and the plate hammer consumption is large. In response to this problem, the following article will introduce the countermeasures to reduce the consumption of the impact crusher plate hammer.

1130003

01 Try to use a good quality board hammer

In view of the quality problem of the plate hammer, Songyuan Industry suggests the selection of the original crusher manufacturer's plate hammer, which basically meets the quality requirements.

02 Re-make the bolt mold

The oval head of the bolt can make good contact with the contact surface of the hammer screw hole of the plate. At the same time, the thickness of the bolt thread is controlled within the dimensional tolerance. The end of the thread is machined into the unloading groove to prevent the stress concentration and fracture.

03 Strengthen usage and maintenance management

First of all, when the plate hammer is installed, the sand and burr of the bolt holes and notches of the plate hammer must be removed to make the connection flat; Secondly, when fastening the plate hammer bolt, it is necessary to hammer the oval head while fastening it; In addition, about half an hour after operation, it is necessary to check the fastening of the bolts in time, and then spot weld the nuts and threads to prevent loosening.

04 When feeding, the material must meet the equipment requirements

Before feeding, the operator must first carefully read the crushing range of the equipment, because the hardness of the material broken by different crushers is different, and the material should be treated before the crushing chamber to reduce the viscosity and water content of the material. In this way, the crusher can play to the maximum performance.

To learn more about our Fangyuan products, please click this link : https://www.fine-mill.com/products.

Send Inquiry

whatsapp

Phone

VK

Inquiry