Tablet Coating Machine
Introduction:
Tablet coating machine, widely used in pharmaceutical, chemical, food, research institutes, hospitals for tablets, pills icing, polishing and rolling food, can also be used for scientific research units to try out new drugs.The coated and polished sugar-coated tablet has a bright appearance, and the complete consolidated coating produced by the crystallization of the sugar on its surface can not only prevent the chip from oxidation and deterioration, moisture or volatilization, but also cover the unpleasant taste when the chip is taken, so as to facilitate the identification of the pill and alleviate the dissolution in the human stomach and intestines.
Working Principle:
In order to make the chip evenly coated on its surface as soon as possible, and to achieve the purpose of polishing, it is necessary to manually spray the chip in the pot with double syrup and mixed slurry. By rotating the pan body clockwise, the sugar coating tablets roll in the pan, and the sliding friction grinding makes it evenly distributed on all the chips. At the same time, hot air is passed into the pot, which can quickly remove the surface water of the tablet, and finally obtain qualified sugar-coated tablets and other finished products. This series of machines is the best equipment for tablet coating process, with the best pot body, stable linear speed to ensure that the tablet in the pot to form the best logistics curve, to meet the coating thickness uniform, bright color without pitting process requirements.

Structural feature:
(1) Motion of the tablet coating machine: This series of machines is a one-way, low-speed continuous rotation of the coating equipment, the main motor through the belt drive - worm gear drive pan body rotation.
⑵ Structural characteristics
a, the center of the machine is equipped with an adjusting hand wheel, which can be used to adjust the tilt Angle of the icing pan according to the tablet load and material exchange performance. (The charge amount of this machine nameplate is based on the Angle of the pot body 30º).
B. Using worm gear as the terminal output of the movement, it has the characteristics of smooth operation and self-locking of the pot.
C, hot air drying device using resistance wire heating, and set high and low temperature switches, easy to control.
Operating procedure:
1. Before operation, we must carefully check whether fasteners in various parts of the machine are loose.
2. Scrub the inside and outside of the icing pan
3, start the main motor, so that the machine running empty for 2 minutes, in order to judge whether there is no fault.
4. After feeding, the main motor button should be pressed first, and then the blower button should be pressed according to the sugar crystallization situation, and the electric heating wire switch should be switched on.
maintenance:
1. The lubricating oil in the gearbox should be replaced regularly as required.
2. sugar-coated pot if not used for a long time should be scrubbed clean, the copper pot should also be coated with oil on its surface to prevent the copper of the pot body from oxidation or moisture after the production of toxic copper compounds.
3. In order to ensure the lubrication conditions of the worm gear pair transmission in the reducer box, the temperature of the box in operation shall not exceed 50 ° C.
4. The sealing ring at the end of the worm shaft should be checked and replaced regularly, generally not more than six months.
5. The machine must be reliably grounded, its grounding resistance should be ≤4Ω.
6. Do not remove electrical appliances and belt protective cover at will.
Technical Parameters-MF-Ultrafine ball mill
|
Model |
Motor Power(KW) |
Graded power(KW) |
Equipment weight(T) | Equipment size(M) | Product fineness(d97=um) |
|
MF0.83×0.5 |
22 |
2.2 |
7.5 |
4.85×2.7×2.2 |
2-100 |
| MF2.2×0.5 |
75 |
6 |
18.8 |
9.2×2.98×2.42 | 2-100 |
| MF3×0.5 | 200 |
15 |
34.2 |
10.5×3.38×3.2 | 2-100 |
| MF3.5×0.5 |
250 |
30 |
47 |
10.5×3.63×3.72 | 2-100 |
| MF4×0.5 |
355 |
44 |
67.5 |
11.4×4.6×4.21 | 2-100 |
| MF4.5×0.5 |
500 |
74 |
83.8 |
11.4×5.1×4.72 | 2-100 |
FAQ
1. Q: Are you a manufacturer, trading company, or a third party?
A: We are a manufacturer, we have our own factory
2. Q: Where is your factory located?
A: Our factory address is: No.9 Yungu Road, Zhutang Town, Jiangyin City, Jiangsu Province, China.
3. Q: How can I get to your factory?
A: Our factory is near Shanghai Airport, Wuxi Shuofang Airport, and Nanjing Airport, we can pick you up at the airport.
4. Q: May I know which payment will be accepted by your company?
A: So far 100% by T/T before shipment, and 30% deposit paid by T/T, balance paid by T/T or L/C are available.
Hot Tags: tablet coating machine, China tablet coating machine manufacturers, suppliers, factory
Previous
No InformationYou Might Also Like
Send Inquiry













