The working process of the tablet press can be divided into the following steps:
1. The punch part of the downward punch (its working position is upward) extends into the middle die hole from the lower end of the middle die hole to seal the bottom of the middle die hole;
2. Use the feeder to fill the middle die hole with drugs;
3, the upper punch part (its working position is downward) from the upper end of the middle die hole into the middle die hole, and down a certain stroke, the powder pressed into a piece;
4. Punch up and lift out the hole. Punch down and rise to push the tablet out of the middle die hole to complete a tablet pressing process;
5. Flush down to the original position and prepare for the next filling.
Tablet press principle
1. Dose control
Tablets have different dosage requirements, the large dose is adjusted by the punch diameter of the die, the small dose is adjusted by the depth of the punch into the middle die hole.
2, tablet thickness and compaction degree control
The dosage of the drug is determined according to the prescription and pharmacopoeia and cannot be changed. There are also requirements for a certain amount of pressure when pressing the tablet, which will also affect the actual thickness and appearance of the tablet. Pressure regulation is essential when pressing the tablet. This is achieved by adjusting the amount of downstroke in the die hole.

3. Adjustment of filling depth (that is, adjustment of pill weight)
Loosen the butterfly screw and loosen the gear clamp. Turn the lower adjusting gear to the left so that the lower punching core rod rises, then the filling depth is reduced (the tablet weight is reduced). After adjustment, press the tooth plate on and tighten the butterfly screw.
4, pressure adjustment (that is, tablet hardness adjustment)
Loosen the connecting rod locking nut, turn the upper punching core rod, turn left to make the upper punching core rod move down, then the pressure increases and the hardness of the pressed tablet increases; On the contrary, turn to the right, the pressure is reduced, the tablet hardness is reduced, and the wrench is stuck on the six sides of the lower part of the punch rod after adjustment, and the connecting rod lock nut is still locked. At this point, the adjustment of the die is basically completed, and then start the motor to test more than ten pieces, check the quality of the piece weight, hardness and surface finish if qualified, you can put into production. In the production process, it is still necessary to check the quality of the tablet at any time and adjust it in time.
5, the disassembly of the die
(1) Remove the upper punch: loosen the upper punch fastening nut, you can pull out the upper punch rod, if the combination is tight, you can clamp the upper punch rod to pull it out, but be careful not to damage the punch edge.
(2) Disassemble the middle die: loosen the fixing screw of the middle die, rotate the lower punch to fix the luning, loosen the butterfly screw and loosen the gear press plate. Transfer the adjusting gear to make the lower punch core rod rise 10 mm, gently turn the handwheel, so that the lower punch core rod will push out part of the mold, and take out the mold by hand. If the mold is closely matched in the hole, do not force the hard top of the handwheel to avoid damage to the machine. At this time, the mold plate must be removed and then take out the mold.
(3) Remove the lower punch: first screw the lower punch fixing screw, and then turn the handwheel to raise the lower punch core rod to the highest position, you can pull out the upper punch rod by hand. If the fit is tight, you can use hand pliers to clamp out (be careful not to damage the edge of the punch).
(4) After the die is removed, it is necessary to rotate the adjusting gear, so that the lower punch core rod is removed by about 10 mm, and the rotation of the handwheel makes the lower punch core rod rise to the highest position, and its top is not higher than the bottom surface of the die plate (this step is not ignored, so as to avoid the accident of the lower punch core rod and the middle die when it is used again). Finally, screw on the underflush setting screw.
To learn more about our Fangyuan products, please click this link :https://www.fine-mill.com.
Our WhatsApp:+86 15896498575





